DiyLightAnimation
Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Home
Wiki
Blog
Chat
Help
Login
Register
DiyLightAnimation
»
Fun
»
The Porch
»
Rays 27 channel DMX board
« previous
next »
Print
Pages: [
1
]
2
Author
Topic: Rays 27 channel DMX board (Read 2709 times)
kjam22
Sr. Member
Posts: 170
Rays 27 channel DMX board
«
on:
August 25, 2012, »
Anyone using one of Ray's 27 channel DMX boards? You are not allowed to view links.
Register
or
Login
I am looking for a little guidance on how I would configure this in LSP
Logged
kevr
Full Member
Posts: 81
Re: Rays 27 channel DMX board
«
Reply #1 on:
August 25, 2012, »
From what I understand these are simply a DMX controller with a selectable DIP switch start address, therefore you could just select a DMX controller in LSP.
These are then set to be a 9 channel RGBcontroller.
Kev :-)
Logged
Grandad get the lights ready
dpitts
Restrictive
Sr. Member
Posts: 466
Re: Rays 27 channel DMX board
«
Reply #2 on:
August 25, 2012, »
I am using 7 of them. What question do you have?
Logged
kjam22
Sr. Member
Posts: 170
Re: Rays 27 channel DMX board
«
Reply #3 on:
August 25, 2012, »
How do you hook up DMX to them since they have the round connection on board? I am assuming I can replace it with a RJ45 some how but dont have one to look at yet.
Logged
dpitts
Restrictive
Sr. Member
Posts: 466
Re: Rays 27 channel DMX board
«
Reply #4 on:
August 25, 2012, »
I replace all of mine with 10" of cat5 cable and RJ-45 connector. I then use RJ-45 coupler to connect to cat5 cable. I will take pictures and post them.
Logged
Steve Gase
Sr. Member
Posts: 2915
Re: Rays 27 channel DMX board
«
Reply #5 on:
August 25, 2012, »
There is a wiki page on the cat5 conversion cable:
You are not allowed to view links.
Register
or
Login
I've got a 27-channel controller and it works well.
Logged
You are not allowed to view links.
Register
or
Login
| 110K channels, 50K lights | Nutcracker, Falcon, DLA, HolidayCoro
chrisatpsu
Sr. Member
Posts: 3729
ahhh, yes... my new blink-i-nator 3000!!!
Re: Rays 27 channel DMX board
«
Reply #6 on:
August 25, 2012, »
keep in mind that graphic is for the male plug.. remember the female plug is reversed pins 1 & 2
reference...
You are not allowed to view links.
Register
or
Login
Logged
To rule the entire tri-state area! What's that? Perry the Platypus!!!
TexasStingray
Coop Manager
Sr. Member
Posts: 791
Re: Rays 27 channel DMX board
«
Reply #7 on:
August 25, 2012, »
I think they support much more current than a single RJ-45 cable can handle so if you use the RJ-45 for power be careful.
Logged
Scott Wanner
TX
Watch my videos
You are not allowed to view links.
Register
or
Login
dpitts
Restrictive
Sr. Member
Posts: 466
Re: Rays 27 channel DMX board
«
Reply #8 on:
August 25, 2012, »
I removed the XLR connectors on 5 of my controllers but on two of them I kept them on. You can solder cat 5 cable onto the bottom of board if you want to keep them.
Logged
rm357
Sr. Member
Posts: 1282
31088
Rays 27 channel DMX board
«
Reply #9 on:
August 25, 2012, »
Power is not supplied through the cat 5. These boards require a separate power supply.
Logged
Robert
Warner Robins, Georgia, USA
kjam22
Sr. Member
Posts: 170
Re: Rays 27 channel DMX board
«
Reply #10 on:
August 25, 2012, »
Thanks for all of the information! I am going to order a couple of these to run some "dumb" strings. I continue to be amazed at how helpful everyone is - thanks again
Logged
dpitts
Restrictive
Sr. Member
Posts: 466
Re: Rays 27 channel DMX board
«
Reply #11 on:
August 25, 2012, »
If you order them from Ray please note that you can get the female four conductor waterproof pigtails in longer lengths. I think mine were 40 cm. Made it easy to have connectors reach the outside of enclosure. Also please see this mod to increase current output. Look at post #48 from user 'AAH'. I have modified all my boards. I have attached a pic of one.
You are not allowed to view links.
Register
or
Login
«
Last Edit: August 25, 2012, by dpitts
»
Logged
rm357
Sr. Member
Posts: 1282
31088
Rays 27 channel DMX board
«
Reply #12 on:
August 26, 2012, »
Interesting...
If you start running the current up, you may want to consider heat sinks on the output devices as well...
Logged
Robert
Warner Robins, Georgia, USA
sielbear
Sr. Member
Posts: 214
Re: Rays 27 channel DMX board
«
Reply #13 on:
August 30, 2012, »
I've ordered 9 for use this year. Hope they work!!!
Logged
IndianaChristmas
Patron Member
Sr. Member
Posts: 304
Re: Rays 27 channel DMX board
«
Reply #14 on:
August 30, 2012, »
Which power supply are people getting for this controller? The one below?
You are not allowed to view links.
Register
or
Login
Thanks.
Logged
Print
Pages: [
1
]
2
« previous
next »
DiyLightAnimation
»
Fun
»
The Porch
»
Rays 27 channel DMX board