DiyLightAnimation
Software => Light Show Pro => Topic started by: dannyct on October 10, 2011,
-
I'm having a problem with LSP2 locking up when "enable" the output and play the sequence.
Here is what I did:
1. Enable the output.
2. Play the output (DMX signal was sent to Lynx express, but there was a huge delay), so then
3. I click on the "Stop" button, at this point, LSP2 lockup and would not response.
I end-up using the "End Task" to force close LSP2.
Please help!!!
I have tested all three controllers using the LSP feature (right click on controller and go to to test Controller hardware). Everything was working in hardware test mode.
What is going on. I just purchased this software yesterday. I hope i'm not wasting my money on this.
Please help!!!!
My Setup Info as follows:
Windows 7 64bit
LSP2 - 2.0.11271.743
3 Lynx Express
Lynx Dongle
-
What controller are you adding in LSP? Should be Enttec DMX Pro Based Device. Have you tried the hardware controller test? Right-click on the controller and select Test Contorller Hardware. Also, try and optimize your sequence first. Right-click on the audio layer, select Maintainance Tools and select optimize entire sequence. Almost all of the time LSP will start responding again, but may take sometime.
-
Yes, as I mentioned in my post earlier, I have tested using the "Test Controller Hardware" from LSP2. All channels are up and response to the test.
Just did it with optimize the sequence.
No luck.
What controller are you adding in LSP? Should be Enttec DMX Pro Based Device. Have you tried the hardware controller test? Right-click on the controller and select Test Contorller Hardware. Also, try and optimize your sequence first. Right-click on the audio layer, select Maintainance Tools and select optimize entire sequence. Almost all of the time LSP will start responding again, but may take sometime.
-
I wonder if you are using the most current build. v2_0_11268_2059
-
I wonder if you are using the most current build. v2_0_11268_2059
I'm using "LSP2 - 2.0.11271.743" (at least that is what the LSP telling me, when I go to "About" to check on the version
I just purchased yesterday, installed and ran the update.
-
I wonder if you are using the most current build. v2_0_11268_2059
I'm using "LSP2 - 2.0.11271.743" (at least that is what the LSP telling me, when I go to "About" to check on the version
I just purchased yesterday, installed and ran the update.
__________________________
I did it!!!
The following steps should fix the locking up problem when click on STOP & PAUSE:
1. Right Click on Controller Bar
2. Go to "Configure Controller Output Plug-in"
3. Under Effect Refresh (it was on 30) I changed it to 320.
And that should fix with locking-up when click on STOP & PAUSE.
-
What is the speed of your machine? Have you tried other values like 60?
-
What is the speed of your machine? Have you tried other values like 60?
I have Q6600 2.8Ghz Quadcore.
I have tried lower values, the lower I go, the problem starting to come back again.
I also noted that, when I set the value at 160 - LSP locking-up when I press the PAUSE botton. The stop button works fine at this value.
Therefore, I increased the value to 320 and the PAUSE and STOP button are now working perfectly.
-
What is the speed of your machine? Have you tried other values like 60?
I'm not sure at what value should work best. I've tried with 200 and it works fine when press the stop and pause.
I guess, I need to spend sometime to try others values.
Any suggestion?
-
Not really sure. The values are much higher than normal. Typically between 30 and 60 works well. It sounds like an issue with your com port, but not sure how to best troubleshoot that.
-
At 30 which is the default, the stop works for me but the pause causes lockups. I have an extremely fast alienware laptop I am testing with.
-
Not really sure. The values are much higher than normal. Typically between 30 and 60 works well. It sounds like an issue with your com port, but not sure how to best troubleshoot that.
So, is there a downside for setting value so higher up?