DiyLightAnimation
Hardware => Bobcat DMX Tester => Topic started by: Donny M. Carter on February 14, 2012,
-
Can the Bobcat be programmed to test other DMX controllers? Like a Renard with DMX protocol. Maybe have two different PICs, one for Lynx and one for Renard. Thanks for any info either way!
Donny
-
Does the renard with dmx respond to dmx? Dmx is dmx?
-
The Renard doesn't deal with DMX in the normal way but the tester should still work with it. The trick it to only connect one Renard to it at a time.
-
Thanks guys! Will give it a try!
Donny
-
You'll need a pin converter for Renard. The boards use pins 4 and 5 instead of 1 and 2. But they are reversed from LOR/D-Light (where pin 4 is Data + it becomes Data - )
-
so for clarity of people readin this thread...
Renard uses which pin for data+, -
LOR uses which pin for data +, -
-
LYNX = Data + Pin1 Data - Pin2 (White with orange stripe/Orange)
LOR = Data + Pin4 Data - Pin5 (Blue/White with Blue Stripe)
Renard = Data - Pin4 Data + Pin5 (Blue/White with Blue Stripe) Pins 1 & 2 Gnd
You can find this information in the WIKI
Corrected error for Renard Pins...
-
LYNX = Data + Pin1 Data - Pin2 (White with orange stripe/Orange)
LOR = Data + Pin4 Data - Pin5 (Blue/White with Blue Stripe)
Renard = Data - Pin4 Data + Pin4 (Blue/White with Blue Stripe)
You can find this information in the WIKI
Renard is actually Data - Pin4 Data + PIN 5
and ground on Pin 1 & 2 for the RS-485 protocol.
Please refer to this link for information on all Renard pin outs
http://doityourselfchristmas.com/wiki/index.php?title=Renard_Data_Cables (http://doityourselfchristmas.com/wiki/index.php?title=Renard_Data_Cables)
There is also a DMX (RJ-45) to Renard Connection diagram on the bottom of the above page.
That diagram shows the pin out for a cable adapter that must be used for running DMX data into a Renard, if the Renard is also flashed with the DMX firmware.
-
LYNX = Data + Pin1 Data - Pin2 (White with orange stripe/Orange)
LOR = Data + Pin4 Data - Pin5 (Blue/White with Blue Stripe)
Renard = Data - Pin4 Data + Pin4 (Blue/White with Blue Stripe)
You can find this information in the WIKI
i know, but once someone writes it in a thread, it now becomes searchable for all the future generations of blinky rookies : )
-
LYNX = Data + Pin1 Data - Pin2 (White with orange stripe/Orange)
LOR = Data + Pin4 Data - Pin5 (Blue/White with Blue Stripe)
Renard = Data - Pin4 Data + Pin4 (Blue/White with Blue Stripe)
You can find this information in the WIKI
i know, but once someone writes it in a thread, it now becomes searchable for all the future generations of blinky rookies : )
Is renard using pin 4 for both positive and ground?
-
that would not be possible. This is a typo. Pin 5 is positive and pin 4 is ground.
-
it's not really ground, but more of the negative voltage
-
That's not really correct. The RS485 ues a differential voltage. When the + is a t 5V and the - is at 0V that is a positive differential and is considered a 1, when the - is at 5V and the + is at 0V tht is considered a negative differential and is considered a zero. There is no negative voltage on either wire but you are correctin saying that neither is a ground so I was wrong there. Pin 4 is the negative lead, not the ground.
-
Since there have been multiple back and forths, could someone summarize in table form the accurate info?
when I saw a latter message with incorrect info i missed that there had already been a correctio, then follow-on discussions ensued, and we missed seeing a final conclusion.
i think most of the threads could benefit for a final summary.
-
Here is the updated table.
LYNX = Data + Pin1 Data - Pin2 (White with orange stripe/Orange)
LOR = Data + Pin4 Data - Pin5 (Blue/White with Blue Stripe)
Renard = Data - Pin4 Data + Pin5 (Blue/White with Blue Stripe)
-
USE: Data+ Data- 586B (most used) 586A
LYNX Pin1 Pin2 (1)White Orange / (2)Orange (1)White Green / (2)Green
LOR Pin4 Pin5 (4)White Blue / (5)Blue (4)White Blue / (5)Blue
Renard Pin5 Pin4 (5)Blue / (4)White Blue (5)Blue / (4)White Blue