DiyLightAnimation

Hardware => Lynx USB DMX Dongle => Topic started by: pete peters on March 14, 2015,

Title: Need Version 1 Hex File
Post by: pete peters on March 14, 2015,
I flashed my version 1 dongle with the Version 2 Hex file and now it will not work. I think I need the version 1 Hex but I can not locate it.

Anyone know where I might find it?

Thanks

Pete P
Title: Re: Need Version 1 Hex File
Post by: jnealand on March 14, 2015,
I can't prove it, but I'm thinking there are only two firmware files for the dongle. 1 for DMX and 1 for Pixelnet.  The only difference I remember between the v1 and v2 boards is the added LEDs.  But my memory has failed me before, wait to see if someone confirms or denies my memory.
Title: Re: Need Version 1 Hex File
Post by: tbone321 on March 14, 2015,
It was the LED's and a jumper that was supposed to put the dongle into test mode but the test mode part of the firmware was never completed.
Title: Re: Need Version 1 Hex File
Post by: tbone321 on March 14, 2015,
You are not allowed to view links. Register or Login
I flashed my version 1 dongle with the Version 2 Hex file and now it will not work. I think I need the version 1 Hex but I can not locate it.

Anyone know where I might find it?

Thanks

Pete P

As Jim indicated, there are two firmware's.  One for DMX output and the other for PixelNet.  Make sure that you have the correct firmware loaded and that the sequence software is configured to work with the DMX dongle with the correct output.
Title: Re: Need Version 1 Hex File
Post by: pete peters on March 15, 2015,
Thanks Guys!

I have used the proper hex file and the proper check sum comes up when I program it with the PicKit 3

When I go to device manager in Windows, the notification tone goes off when I plug in the dongle, but the com port does not show up in the list.
I have another dongle and it gets the notification tone and it shows com port 7 on the list.
What should I check now?

Thanks

Pete P
Title: Re: Need Version 1 Hex File
Post by: tbone321 on March 15, 2015,
Make sure that you have installed the FTDI drivers prior to plugging the USB dongle in.  If not, then Windows will install its driver which will not work.
Title: Re: Need Version 1 Hex File
Post by: pete peters on March 15, 2015,
You are not allowed to view links. Register or Login
Make sure that you have installed the FTDI drivers prior to plugging the USB dongle in.  If not, then Windows will install its driver which will not work.

The FTDI drivers are installed.  Check Sum is correct. Still not seeing it in the Com Port list..  My other dongle is working fine.  What else do I look at now?

Thanks
Pete P
Title: Re: Need Version 1 Hex File
Post by: tbone321 on March 15, 2015,
What lights are lit on the dongle board?
Title: Re: Need Version 1 Hex File
Post by: pete peters on March 15, 2015,
You are not allowed to view links. Register or Login
What lights are lit on the dongle board?

This is Version 1  It has no lights

Thanks

Pete P
Title: Re: Need Version 1 Hex File
Post by: caretaker on March 16, 2015,
Try plugging it into another USB port, I have had that happen when using two different USB dongles.
You are not allowed to view links. Register or Login
Thanks Guys!

I have used the proper hex file and the proper check sum comes up when I program it with the PicKit 3

When I go to device manager in Windows, the notification tone goes off when I plug in the dongle, but the com port does not show up in the list.
I have another dongle and it gets the notification tone and it shows com port 7 on the list.
What should I check now?

Thanks

Pete P
Title: Re: Need Version 1 Hex File
Post by: tbone321 on March 16, 2015,
Did the dongle work prior to the firmware update?
Title: Re: Need Version 1 Hex File
Post by: tbone321 on March 16, 2015,
Also, when you get the notification tone, what changes in the hardware listing?  Somewhere there is a USB device being added and you will need to see what it is. 
Title: Re: Need Version 1 Hex File
Post by: pete peters on March 16, 2015,
You are not allowed to view links. Register or Login
Also, when you get the notification tone, what changes in the hardware listing?  Somewhere there is a USB device being added and you will need to see what it is.

The dongle was showing up as "other device - DLP USB245M" on the device manager list.  When I saw this I check to see if the driver was installed. I had windows install the driver and WA- LA  the dongle has an assigned Com Port  It works fine!

Feel kind of dumb for not realizing this sooner but THANKS to you I found the problem!

THANKS VERY MUCH for all your help!!!

Pete P
Title: Re: Need Version 1 Hex File
Post by: tbone321 on March 16, 2015,
Glad that you got it working.