New release v.0.0.716.1058 (RC3)

[LightShowPro]

New release of LightShow Pro Release Candidate Three (RC3) today (v.0.0.716.1058)

changes:
-Drawing single cell effects can now be done with a single click and do not require a short-drag.
-Clipboard drawing feature for fast ramps. (copy cells, then select a region while holding the shift-key to draw clipboard contents)
-multi-channel clipboard drawing effects supported.
-configurable Low and High bandwidth remote ports to accommodate Jukebox functionality.
-Integrated contextual help (pressing F1 while in most areas)
-Improved LOR and Aurora importing capabilities.
-Multi-channel drawing tools now split equally across all designated channels.
-Jukebox touchpanel dashboard for in-yard-jukebox functionality.
-enhanced twitter integration with scheduler.
-cue-position now moves in wave area while using TouchMode
-drawing effects over other effects no longer cause run-off effect cells.
-improved ramps when less than .05 sec
-and much more!

This download is available via the LightShow Pro updater as well as from the LightShowPro.com downloads section.


Enjoy the latest changes as we prepare for a final release candidate!
LSP team

[rrowan]

Hi David

That sounds Awesome

I'll grab a copy and check it out after my son's school event tonight

Many thanks

Rick R.

[rmonty]

Just FYI to those using the remote capability either through the mobile or jukebox.  If you have a router on your home network, you can actually use the remote functionality anywhere you have internet access.  You will have to setup port forwarding through your router.

[wbuehler]

Awesome

Thanks for all the hard work.

Bill

[RJ]

Cool Stuff!
RJ

[vairmoose]

Sounding better and better    

Downloading a copy now...  will check it out later.

Larry

[wbuehler]

Cool

It prompts for start channel now 


Just a cosmetic thing but I noticed that when I added a second controller it labeled the first channel of the second controller as Channel Number 1 instead of 17 in this case.
I have attached a pic.  The name can be updated so it's just a cosmetic thing.

Bill

[rmonty]

Be sure and try out the new chase feature.  Like David said above, copy the pattern you want to chase.  Then click the chase tool and hold down the shift key while dragging where you want the chase to occur.  Let us know how it works out for you.

[PJNMCT]

This download is available via the LightShow Pro updater as well as from the LightShowPro.com downloads section.

I'm sure it's just me, but where's the updater?

-Paul

[wbuehler]

Yup I am trying it now.  But I am not sure if I am doing it correctly.
It is Cool I can hold down shift and select a range of cells over a period of time works slick.

I made a group of channels do a ramp so I had some data to copy.  I then switched over to chase and used the shift key to select a group of channels over a range of time.
when I let the mouse button go it did copy the ramp data to the selected channels over the selected range of time.  But it did the same over all the selected channels and did not seem to offset the ramp effect across them.  So the end result did not look like a chase.

And I doing it wrong?

Bill

[rrowan]

This download is available via the LightShow Pro updater as well as from the LightShowPro.com downloads section.

I'm sure it's just me, but where's the updater?

-Paul

Hi Paul

It seems like the updater is a background program. After a few minutes in LSP it just popped up a Confirm box asking if I wanted to download the new update.

Rick R.

[PJNMCT]

Thanks Rick,

Couldn't wait...just downloaded and installed.

-Paul

[rrowan]

Hi Dave or Ryan,

Question about Chase

Paste selection at the nearest intervals.

If you select No then it adds extra timing intervals. Is there a way to remove those extra intervals if later I don't want the chase? I know I can do it one at a time but that is time consuming. Pretty much reset the intervals back to what it was before the chase.

Thanks

[rmonty]

Right now no.  What LSP is trying to do is hold the copied effects lengths the same, so it creates intervals to do that if necessary.  If you are using 1/10th intervals or something like that, then it probabaly wouldn't create new intervals since all intervals would be the same length of time.  It's kind of a side affect of being able to put your intervals where ever you want.  Currently there is no undo for interval creation.

Ryan

[LightShowPro]

Hi Dave or Ryan,

Question about Chase

Paste selection at the nearest intervals.

If you select No then it adds extra timing intervals. Is there a way to remove those extra intervals if later I don't want the chase? I know I can do it one at a time but that is time consuming. Pretty much reset the intervals back to what it was before the chase.

Thanks

Hi RRowan,
if you choose to get rid of the intervals/timings you can do them one at a time or you can select a range in the waveform, right-click on the slection and click on the remove intervals in range. this will remove all of the intervals in the selected range. you can also do this in the effect grid by looking at the right-click menu items.

we will be looking at improving the undo model at some point in the near future.

hope this helps,
David