Search results

Page title matches

• FAQ Toroid Low voltage power
  == AC Power for Low Voltage Light Strings. == Low voltage in this article will refer to all AC voltages under 50v. Whilst these may b
  8 KB (1,490 words) - 09:09, 21 April 2008

Page text matches

• Lynx
  ...ng equipment as well as be assured that it could run up to 512 channels at low event times on one port (DMX universe). ...gh voltage is isolated from the digital side of the board so there is very low risk of anything getting into the DMX feed and damaging any digital equipme
  3 KB (617 words) - 07:25, 2 May 2008
• FAQ Toroid Low voltage power
  == AC Power for Low Voltage Light Strings. == Low voltage in this article will refer to all AC voltages under 50v. Whilst these may b
  8 KB (1,490 words) - 09:09, 21 April 2008
• Equipment
  *Need to know if Lynx hardware works in your region? [[Lynx Voltage Info]] ...//diylightanimation.com/index.php?action=dlattach;topic=3425.0;attach=4057 Low Power]
  48 KB (6,535 words) - 23:58, 3 December 2018
• FAQ
  ===[[LVT|Low Voltage Transformers]]=== *[[Lynx Voltage Info]]; Describes which Lynx hardware that can be used on different voltage
  6 KB (994 words) - 08:31, 22 September 2012
• Tiger SSR16 Detail
  If the amount of current you are drawing is low then there is provision for a link to be added so that only one AC input is The DMX daughter board requires a solid 5v DC voltage. This voltage is supplied by the onboard TL783 SMD Regulator. This regulator allows for a
  5 KB (998 words) - 13:33, 2 October 2009
• LVT
  Low Voltage Transformers
  1 KB (238 words) - 07:19, 24 July 2008
• Freestyle Manual
  ...t. This insures the regulator can move the heat to the heat sink fast with low resistance. Once you have applied some. Then attach the regulator to the he ...careful doing these measurements as the larger resistors and fuse has high voltage on them.'''
  23 KB (4,350 words) - 10:01, 18 January 2011
• Glossary
  ...ity is that of plumbing and water: the pressure of water in a pipe is like voltage, while the flow of the water in a pipe is like amps. ...ristmas light world, FCC Part 15 is discussed because it regulates the way low-power FM transmitters, which are used in the Christmas lights community to
  19 KB (3,113 words) - 22:25, 3 May 2012
• Pic Dimming
  ...ing the other way. So this is when our triacs turn off as when there is no voltage there can be no current. To control how much "Power" we get to the lights w ...t about 80% of your dimming range with it not doing anything at the ends / low values and high values
  6 KB (1,294 words) - 15:58, 12 December 2008
• Lynx Voltage Info
  '''Question? What Lynx hardware will work with my voltage and hertz (50/60)?''' | '''Low volts (24/36)'''
  2 KB (321 words) - 19:17, 26 January 2009
• Manual Lynx
  ...the pn on the dip should be 8x-2-224). They go just above the Warning High Voltage Line. It can sometimes matter as you will see which direction these sips ar ...t over use solder. These pins are close together and will be carrying line voltage so we don’t want any short circuits here.
  44 KB (8,150 words) - 19:20, 13 November 2010
• Beginners
  :DMX is a communications protocol that "talks" on low voltage wiring and controls entertainment devices. Some devices are lights and serv * Can control low voltage SSRs
  12 KB (2,010 words) - 22:55, 10 January 2010
• Manual MR16 v1
  If you are not using them and running the board as a low current constant current driver leave them out. Now let’s add the 7805 voltage regulator. It is a three pin device and goes on the right of the clock. Mak
  15 KB (2,715 words) - 18:14, 5 August 2012
• Manual PixelnetSplitter
  Locate the voltage regulator. Insert it at U5 with the metal tab facing the upper edge of the ...Make sure the terminals labelled 1 and 2 are located closest to the HIGH VOLTAGE label. Solder the leads.
  8 KB (1,531 words) - 17:26, 25 November 2012